logo

How to Evaluate the Pore Structure of Zirconia from a Macroscopic Perspective?

2026/11/16

Latest company news about How to Evaluate the Pore Structure of Zirconia from a Macroscopic Perspective?
1. Can Zirconia Porosity Be Judged from Macroscopic Properties?

The pore structure of zirconia cannot be accurately determined through visual inspection or conventional macroscopic material parameters alone.

Properties such as bending strength, translucency, color, and bulk density may provide indirect information about material characteristics, but they cannot directly reveal the amount and connectivity of open pores inside zirconia.

For evaluating the pores that allow liquids to enter a ceramic material, open porosity is one of the most relevant indicators.

Open porosity refers to the proportion of interconnected pores that communicate with the external surface and can be penetrated by a liquid. Unlike closed pores, these pores provide potential pathways for liquid penetration.

Therefore, measuring open porosity can help characterize the liquid-accessible pore structure of zirconia and provide a basis for further investigating its staining-liquid absorption behavior.

At present, no experimental open-porosity results are available for the zirconia materials discussed here. The following section introduces a laboratory method that can be used to measure this property.

latest company news about How to Evaluate the Pore Structure of Zirconia from a Macroscopic Perspective?  0

2. How Is Open Porosity Measured?

One commonly used approach for measuring the apparent porosity of ceramic materials is the Archimedes method (liquid displacement method).

This method determines open porosity by measuring the weight of a dry specimen, its weight after liquid impregnation, and its apparent weight while suspended in the liquid.

The method is described in ISO 18754:2020, Fine ceramics — Determination of density and apparent porosity.

2.1 Required Equipment

The experiment generally requires:

  • Analytical balance

  • Drying oven

  • Distilled or deionized water

  • Vacuum chamber or suitable heating equipment

  • Beaker or immersion container

  • Suspension wire or weighing basket

  • Thermometer

2.2 Sample Preparation

Prepare representative zirconia specimens with consistent dimensions and surface conditions.

Before testing:

  1. Clean the specimen to remove surface dust and contaminants.

  2. Dry the specimen in an oven until a constant mass is achieved.

  3. Allow it to cool under controlled conditions.

  4. Record the dry mass.

The sample should be weighed accurately because small measurement errors can affect the calculated porosity.

2.3 Experimental Procedure

Step 1: Measure the Dry Mass

Weigh the dried zirconia specimen in air and record its mass as (m_1).

Step 2: Impregnate the Specimen with Liquid

Place the specimen in distilled or deionized water.

Liquid impregnation can be performed using either of the following approaches:

  • Vacuum impregnation: Reduce the pressure to help remove air trapped inside accessible pores, allowing water to penetrate them.

  • Boiling impregnation: Use controlled heating to facilitate the removal of trapped air and liquid penetration.

The specimen must be sufficiently impregnated before proceeding.

Step 3: Measure the Suspended Mass

Suspend the impregnated specimen completely in water and record its apparent mass as (m_2).

Make sure the specimen does not touch the container walls or bottom.

Step 4: Measure the Saturated Mass

Remove the specimen from the water and gently wipe away excess surface water without extracting water from the open pores.

Weigh the saturated specimen in air and record its mass as (m_3).

latest company news about How to Evaluate the Pore Structure of Zirconia from a Macroscopic Perspective?  1

3. How to Calculate Open Porosity

Once the three mass measurements have been obtained, open porosity can be calculated using the following formula:

[
P_o=\frac{m_3-m_1}{m_3-m_2}\times100%
]

Where:

  • (P_o): Apparent open porosity (%)

  • (m_1): Dry mass of the specimen in air (g)

  • (m_2): Apparent mass of the saturated specimen suspended in water (g)

  • (m_3): Saturated mass of the specimen in air (g)

The numerator represents the mass of liquid entering the open pores, while the denominator represents the mass of liquid displaced by the specimen's bulk volume.

The resulting percentage indicates the proportion of the specimen's bulk volume occupied by liquid-accessible open pores.

4. What Do the Results Tell Us?

A higher open porosity value indicates a larger proportion of liquid-accessible pore volume. A lower value indicates a smaller proportion.

For zirconia staining research, this measurement can help investigate whether differences in open pore volume are associated with differences in staining-liquid uptake.

However, open porosity alone does not describe the complete pore structure. Pore size, pore connectivity, pore distribution, and liquid properties can also influence actual liquid penetration.

Therefore, open porosity should be considered a structural indicator rather than a direct measurement of staining-liquid absorption.

5. Conclusion

Macroscopic properties such as density, strength, and translucency cannot independently provide an accurate assessment of zirconia's open pore structure.

The Archimedes method provides a practical approach to measuring apparent open porosity in ceramic materials. By establishing a consistent testing procedure, manufacturers and researchers can obtain quantitative data for evaluating accessible pore volume.

Further comparative staining experiments are still necessary to establish the relationship between open porosity and actual staining-liquid absorption.

Previous: Next: There Is No More
Back To List